Redding Case Preparation & Trimmers

Model 1400-XT Case Trimming Lathe

Redding "case trimming lathes" are the only case trimmers on the market that turn the case and not the cutter. This feature guarantees a perfectly square case mouth with every cut.

The Model #1400-XT Case Trimming Lathe uses a cast iron frame that has been extended to handle all the latest long action cartridges. The frame is cast iron because it is a perfect bearing surface, will not wear out and will maintain its precision and alignment for years of service.

This case trimmer was designed using precision lathe principles. The TiN coated cutter is held stationary while the case is turned; this produces cases that are perfectly square, resulting in increased accuracy from your handloads.

The Model #1400-XT Case Trimming Lathe is supplied with the following:
• Universal collet (no others to buy)
• Replaceable Titanium Nitride (TiN) coated cutter
• Six pilots - .22 cal., 6mm, .25 cal., .270 cal., 7mm and .30 cal.
• Two neck cleaning brushes (.22 thru .30 cal.)
• Large and small primer pocket cleaners.

Model 1400-XT features:

• Cast iron frame to last a lifetime.
• Universal collet fits all popular cases – no others to buy.
• Handles 3" case length with ease.
• New replaceable cutter with TiN (Titanium Nitride) surface treatment.
• Coarse and fine adjustments for case length.
• Storage holes for pilots.

$155.00 AU incl GST
Add to Shopping Cart
Check Out

NEW! – Model 2400 Match Precision Case
Trimming Lathe

The new Model #2400 Case Trimming Lathe uses the extended cast iron frame of our Model #1400-XT to maximize case length capacity.

The innovative new push button chuck lock simplifies loading and unloading while facilitating perfect alignment of the case and pilot. The design of the new push button chuck lock also increases case length capacity; accommodating not only the latest long action cartridges but old time classics as well. Case lengths up to 3-1/4" can be handled.

The most noteworthy feature is the new Micrometer which adds precision and repeat-ability to the case length adjustment. Changes of as little as .001" can be easily dialed in.

The Model 2400 Case Trimming Lathe is supplied with the following:
• Universal collet (no others to buy)
• Replaceable Titanium Nitride (TiN) coated cutter
• Six pilots - .22 cal., 6mm, .25 cal., .270 cal., 7mm and .30 cal.
• Two neck cleaning brushes (.22 thru .30 cal.)
• Large and small primer pocket cleaners.

Model 2400 features:

• New micrometer…easy adjustments of .001".
• Cast iron frame to maintain precision alignment.
• New push button collet chuck is ideally suited for use with optional power adapter.
• Handles 3-1/4" case length.
• Universal collet fits all popular cases – no others to buy.
• TiN (Titanium Nitride) coated replaceable cutter.
• Storage holes for pilots.

$250.00 AU incl GST
Add to Shopping Cart
Check Out

Pilots

3/16” Shank Pilots may also be used on Hornady and Forster trimmers.

When ordering, please specify requires caliber in the comments during checkout.

$7.00 AU incl GST
Add to Shopping Cart
Check Out

Replacement Cutters

New replaceable (TiN) Titanium Nitride Coated high speed cutters.

TiN Cutter (17 & 20 caliber) *

$32.00 AU incl GST
Add to Shopping Cart
Check Out

TiN Cutter (Standard)

$32.00 AU incl GST
Add to Shopping Cart
Check Out

TiN Cutter & Shaft Complete

$45.00 AU incl GST
Add to Shopping Cart
Check Out

Optional Power Adapter

Optional Power Adapter with 1/4” hex for use with cordless screwdrivers.

$15.00 AU incl GST
Add to Shopping Cart
Check Out

Deburring Tool

Removes burrs and bevels case mouths for easy bullet seating. Hardened precision ground flutes make clean, easy, chatter-free cuts. Accepts all cases from .17 to .45 caliber.

$32.00 AU incl GST
Add to Shopping Cart
Check Out